Frequently asked questions about video conferencing (meet)
1. When entering a room
1.1. The client application page does not open
Check firewall settings or ask the system administrator whether access to the url the client navigates to is open.
1.2. Cannot connect to the room (connection attempts are shown)
If there are 3 IP addresses on the server
Access over wss and rtp is closed.
If there is 1 IP address on the server and the url and wss address differ
The SSL certificate has expired; check the browser console for a cert invalid error (or similar text)
2. Inside the room
2.1. Audio and video questions
2.1.1. Video / audio stutters and disappears
The problem can be divided into the following types:
-
Packet loss (bad network)
In this case problems may occur with both audio and video.
The server and client have retransmission mechanisms to combat this. If the problem is observed — lower the room quality parameters and find out what is wrong with the network. -
Room and server settings mismatch ("You want too much")
In this case problems may occur only with video, since audio has priority on the server and does not depend on video settings.
The problem:-
may occur for a single participant — server settings exceed the participant’s network capabilities
-
may occur for all participants to varying degrees — quality is lowered or other participants' video is disabled
The problem is the mismatch between server settings and the network capabilities of the server and clients.
The following settings must be checked for consistency: -
quality — "Room" tab — "Quality" setting
-
layout — "Room" tab — "Participant layout" setting (if present and should it be?), or clarify which layout participants usually select
-
per-participant channel width limit in the server configuration, specified in the master domain settings — domain.settings.meet_config
-
The channel width limit is specified based on the following calculations:
-
Server
-
The outgoing channel must be at least:
Z * 64KB * N (audio) + Z * (XKB + X/4KB + X/16KB) * M (cameras) → sum over simultaneous rooms
Z — total number of participants
N — maximum number of participants who will enable the microphone
M — maximum number of participants whose video will be displayed in the layout. Complex cases with different layouts for different participants should be calculated by the peak capabilities available for installation by users.
X — camera or screen sharing bitrate set in the room settings -
The incoming channel must be at least:
64KB * N (audio) + (XKB + X/4KB + X/16KB) * K (cameras) → sum over simultaneous rooms
X — camera or screen sharing bitrate set in the room settings
N — maximum number of participants who will enable the microphone
K — maximum number of participants with cameras on
-
-
Client
-
The outgoing channel must be at least:
100KB (audio) + XKB (camera)
X — camera bitrate set in the room settings -
The incoming channel must be at least:
100KB * N (audio) + (XKB + X/4KB + X/16KB) * M (cameras)
N — maximum number of participants who will enable the microphone
M — maximum number of participants whose video will be displayed in the layout.
X — camera bitrate set in the room settings
-
The following should be reconciled:
-
For the server. The channel width available on the server with the calculated values for outgoing and incoming channels
-
For each participant. The parameters set in the server configuration (mediasoup → webRtcTransportOptions → consuming | producing) and each participant’s channel width.
-
Server problem
Check server load:
* cpu
* swap — if it started being used, quality problems may occur; reduce RAM load or increase RAM volume
Commands for emergency clearing of unused memory and swap:
sync; echo 3 > /proc/sys/vm/drop_caches
sudo swapoff -a && sudo swapon -a
2.1.2. We enable screen sharing (or video) and quality is bad for everyone
Check the presentation resolution and bitrate in the room settings: "Room" tab — "Quality" setting
Check room and server settings consistency — whether the channel width allows broadcasting in the selected quality to the connected number of participants.
2.1.3. No video at all, none
One reason is using a browser not from the supported list. Clarify which one and suggest using a supported one (the list is in the answers to questions).
2.1.4. The user is not heard
Connection quality indicators are displayed in the lower right corner. Find out the color of the second indicator (in the center, labeled "Transmission…" on hover):
-
green — data transmission is working; check which device is selected as the speaker (see below)
-
yellow — sound transmission is disabled; check whether the microphone is enabled in the client application interface
-
red — for some reason there is no connection for transmitting sound to the server. Causes may include: blocking by the regulator, the rtp port range configured on the server is unavailable for this client.
-
gray — the microphone is disabled in the video conferencing client and was not enabled.
Check the device selected as the microphone.
In the center, at the very bottom of the panel, is the microphone icon. To change, select from the drop-down list. If there is no drop-down list, select the required device as the microphone in the system settings.
2.1.5. The user hears no one
Connection quality indicators are displayed in the lower right corner. Find out the color of the first (leftmost, labeled "Reception…" on hover) indicator:
-
green — data reception is working; check which device is selected as the speaker (see below)
-
yellow — sound reception is disabled; check the icon of the device selected as the speaker — it should be green
-
red — for some reason there is no connection for receiving sound from the server. Or there is no traffic from the server. Causes may include: blocking by the regulator, the rtp port range configured on the server is unavailable for this client.
-
gray — there is no participant — sound source; no one is speaking.
Check the device selected as the speaker.
In the upper right corner there is a speaker icon (if absent, click the left arrow) and select from the drop-down list. If there is no drop-down list, select the required playback device in the system settings.
2.1.6. Strong echo / noise from a participant
As a rule this occurs in rooms with several microphones and speakers, where a mixer is used to combine sound (input and output), and the input and output signals "mixed" in one virtual device with input and output. In this case the echo canceller and noise suppressor do not work. Solution: check how the input and output channels are mixed and separate them.
2.2. Other questions
2.2.1. How to raise quality for only one speaker (video / screen share)
Owner or moderator rights are required.
Change individual settings: "People" tab - context menu on the participant row - select "Individual settings".
2.2.2. Lost access (moderator / owner) to the room, what to do?
-
Change or grant owner (or moderator) rights to a participant via the Video conferencing Administrator application
-
Use hidden admin to assign a participant as moderator (do not provide end-user instructions on how to log in as hidden admin, only for your own engineers)
Recommendations:
-
Log in to the system before creating a room (use authorization)
2.2.3. I see no one / only one person, etc.
Check which layout is currently set for the user and change it if necessary.
If only one participant is visible and in the "Options" - "Layout" tab above the layout list it says "Participant: xxx", then by double-clicking on the participant window the layout returns to the previous view; ask them to double-click on the participant window.
3. Other questions
3.1. Which rooms are active now?
Monitoring access by url
https://server_url/meet/monitoring/<reportPassword>
The password is configured in the Meet server configuration